DIY Demolition: Important Dos and Don’ts

Not everybody might have the skills or time to do a complete renovating job. However, nearly anyone can grab a sledgehammer and pry bar and then jump into the early phase of the most projects that is demolition.

Not only it is so pleasurable to finally remove the pink tile that you have always detested or the wall which should have been a window, but also it can save money in the process if you are doing it yourself.

But before you begin to have fun, you have to know several basics, like how to do it safely and how to find out what is hidden behind a wall.

DIY Demolition: Important Dos and Don'ts

Urgent! Don’t forget to protect yourself.

If you are not dealing with a serious environmental threat, for instance, coats of old lead-based paint or asbestos paint since lead contains high toxin that can cause various health problems, you may wear personal protection consisting of safety glasses, a dust mask, and work gloves.

However, if you are digging into insulated walls, it would be much better for you to wear a long-sleeved shirt with closed collars as well as cuffs to guard against skin irritation. If you are dealing with asbestos paint, the recommended measure is hiring a removalist to perform asbestos testing in Sydney (

Although asbestos paint only contains 5 to 10% of asbestos, this amount was sufficient to cause a deadly situation to arise in those to this dangerous substance. Keep your current work area clear enough to give secure footing. Don’t do an activity on a pile of debris. That means you will have to stop regularly–but you will perhaps be ready for the breather.

Do remember that you will be dealing with all the debris a second time when you go to a Dumpster, so cut large parts into smaller pieces so that it will be easier to handle. Additionally, a hammer to crook the business end of nails sticking out from lumber.

Keep safe your home from harm.

To protect other areas of the house, hang plastic sheeting or drop cloths over doorways. Another alternative is to set up a “dirty room” of 1-by-2s coated with plastic sheeting to take in debris and dust in a limited workspace. In spite of that, close and cover heating as well as air-conditioning ducts–any passage that could carry dust to other areas.

Wrapping plastic and sealing edges using tape requires extra time. But the investment will significantly reduce cleanup–like emptying, washing also restoring each item in kitchen cabinets. Demolition dust is prevalent.

Look out for hidden mechanicals.

Outlets, switches, and duct registers give almost obvious clues. However, an interior wall may also hide wires and pipes on route to and from a neighbouring bath or kitchen. Following cutting off the supplies, any pipe or wire can be rerouted. But the main plumbing vent is better left in place.

This pipe with a large diameter often runs from the basement along the roof and connects to all plumbing fixture heading towards. The best and safest procedure to avoid surprises is to demolish surface materials such as tile and then remove a few drywall panels to inspect what is hidden underneath.

Get familiar with your walls.

Partitions only divide area. They can be removed without having to add or replace any framing since they don’t support the building.

On the other hand, bearing walls support the structural weight. They can be removed, but it requires much effort and quite hard. You need to sustain temporary supports when the wall comes down, then provide a permanent header beam to support the load which the wall used to carry.

Usually, all exterior walls are supporting walls and not all, although most, interior walls are partitions. Interior walls that frequently are load bearing incorporate walls stacked in line one story to the other as well as walls along a central stairwell.

It is a difficult subject, and surprisingly some of the contractors do not have the ability to tell the difference before drywall is removed and framing is revealed. But it is an important distinction. Demolish a bearing wall by mistake, and nearby framing is sure to crumble or could even fall to pieces.

Peel off drywall and remove studs.

Use a sabre saw to slice through panels near studs –cutting only through the 1/2-inch thickness—after that cut the large panels and later handle the studs. But it is more usual to get a handhold on the edge of a panel by taking out nails or removing a seam with a flat bar. Next, you can separate the panel in ragged sections using the hand.

Discard the debris.

Usually, you must pay someone to throw away the stuff. To rent a roll-off container is the most efficient alternative is –a Dumpster–available in many sizes. The carting company drops the debris off for several days or weeks, then gathers it up fully loaded when you are finished with demolition.

Click here for more information on doing Demolition yourself.